Filter Warehouse Company provides air conditioning products and services.

Please Print this Form and Fax to FWC at (713) 432-7117 for pricing information.

General:

The filters shall be of the (select one) ______________ type.

(a) High Efficiency Particulate Air Filter (HEPA).
(b) Ultra Low Penetration Air Filter (ULPA).

Performance:

1. Each filter shall be individually tested and certified to furnish overall minimum efficiency of (select one) _____ on .3 micron size particles.

(a) 99.97%
(b) 99.99%
(c) 99.999%

2. Each filter shall have a nominal rating of ______ CFM with a maximum initial resistance to air flow of _____ in. w.g.

3. Each filter shall be scanned prior to shipment and certified that no pin hole leaks exist.

Physical Characteristics:

1. The filter will have the following actual dimensions of _____ high x _____ wide x _____ deep with an acceptable tolerance of +0, -1/8".

2. The filter media shall consist of ultra fine glass microfibers and manufactured into a wet laid high density paper. The media shall be waterproof and fire resistant to 1000 degrees F.

3. The pleats shall be maintained by hemmed safety edge separators produced from ________ (select one).

(a) corrugated aluminum
(b) vinyl coated corrugated aluminum
(c) kraft paper

4. The cell sides of the filter shall be produced from ______ (select one).

(a) 3/4" particle board
(b) 3/4" fire retardant particle board
(c) 3/4" exterior plywood
(d) 3/4" fire retardant plywood
(e) 16 gauge galvanized steel
(f) 18 gauge galvanized steel
(g) .063 gauge aluminum
(h) 16 gauge 304 stainless steel
(i) 16 gauge 409 stainless steel
(j) Other ____________________

5. The sealant/bond securing the media pack to the cell sides shall be made of _______ (select one).

(a) polyurethane
(b) silicone
(c) ceramic
(d) Other _______________

6. The gasket shall be of interlocking dove tail design and be made of _________ (select one).

(a) silicone
(b) ceramic
(c) Other _________________

7. The gasket shall be applied to the _______ (select one) face of the filter.

(a) downstream
(b) upstream
(c) both
(d) none

8. Faceguards, if required, shall be made of _________ (select one).

(a) expanded galvanized steel
(b) expanded aluminum
(c) stainless steel hardware cloth
(d) white vinyl coated expanded metal
(e) Other ____________________

9. Faceguards shall be fastened to the __________ (select one) face of the filter.

(a) downstream
(b) upstream
(c) both
(d) none

10. The filter shall be individually labeled and the label shall provide the following information _________ (select as required).

(a) manufacturer's name
(b) product brand name
(c) test air flow direction
(d) overall DOP penetration
(e) initial resistance to air flow
(f) test air flow rate
(g) serial number
(h) inspector's mark
(i) all of the above
(j) Other __________________

11. Prefilters shall be furnished to extend the life of the HEPA filter specified. The prefilter shall have an Average Atmospheric Dust Spot Efficiency, when tested by ASHRAE Standard 52.1 - 1992 of _________% (select one).

(a) 25%
(b) 60%
(c) 80%
(d) 90%

[ TOP | RESIDENTIAL | COMMERCIAL | HOSPITAL | INDUSTRIAL ]

Filter Warehouse Co.
1310 N. 1st Street Suite C
Bellaire, TX 77401
Phone: 713.432.7969
Fax: 713.432.7117
E-mail: sales@filterwarehouse.com